Glassman LH系列高壓電源

參考價	面議

參考價

面議

具體成交價以合同協議為準

公司名稱 上海卓定電子科技有限公司
品牌
型號
所在地上海
廠商性質其他
更新時間 2024/12/28 9:09:22
訪問次數 1

在線詢價收藏產品點擊查看聯系電話

索取相關資料

促銷詳情

促銷時間：

特價說明：

促銷詳細：

2020年01月08日至 2020年02月08日

特價促銷

模內澆口分離自動化，降低對人的依賴度；傳統的塑膠模具開模后產品與澆口相連，需二道工序進行人工剪切分離，模內熱切模具將澆口分離提前至開模前，消除后續工序，有利于生產自動化，降低對人的依賴。

產品簡介

我也要發布產品信息

LH Series 5 kW Regulated High Voltage DC Power Supplies 1 kV to 100 kV Rack Mount CE Compliant.The L...

詳細信息在線詢價

Glassman LH系列高壓電源

LH Series 5 kW Regulated High Voltage DC Power Supplies 1 kV to 100 kV Rack Mount CE Compliant.The LH family of power supplies are sophisticated, 5 kW, high voltage power supplies with low ripple and noise. They are air insulated, fast response units, with tight regulation. ArcQuench and Arc Sense are features that make the LH series Ideal for Dynamic load environments.

The LH Series are fully compliant with the European Harmonized EMI Directive EN50082-2 and with the European Low Voltage (Safety) Directive, 73/23/EEC.

Glassman LH系列高壓電源特點

From 5% to 99% rated voltage. All units operate down to zero output with very slight degradation of performance.
INPUT:
187-264V RMS, 3-phase, 48-63 Hz, 6500 VA maximum at full load. Less than 20 A/per phase. at 208 VAC. A five position rear terminal block with protective cover is provided.
EFFICIENCY:
Typically greater than 85% at full load.
OUTPUT:
Continuous, stable, adjustment from 0 to rated voltage or current by panel mounted 10-turn potentiometers with 0.05% resolution, or by external 0 to 10 V signals is provided. Linearity is < 1% of rated. Voltage Accuracy is 0.5% of setting + 0.2% rated.
STATIC VOLTAGE REGULATION:
Better than ±0.005% for specified line variations and 0.01% for no load to full load variations.
DYNAMIC VOLTAGE REGULATION:
For load transients from 10% to 99% and 99% to 10%, typical deviation is less than 2% of rated output voltage with recovery to within 1% in 500 μs and recovery to within 0.1% in 1 ms.
RIPPLE:
Better than 0.05% RMS of rated voltage at full load.
CURRENT REGULATION:
When in current regulation mode, better than 0.1%, with 8-100kV models better than 0.2%, from short circuit to rated voltage at any load condition. When in current trip mode the HV output will disable and latch off when the load current reaches the programmed current level. Reset is accomplished by either cycling the AC power or HV ON/OFF buttons, or by toggling the HV enable signal. A switch located on the rear panel allows the selection of current limit modes: onstant current, or current trip.
VOLTAGE MONITOR:
0 to +10 V equivalent to 0 to rated voltage.
Accuracy, 0.5% reading + 0.2% rated.
Impedance is 10 K.
CURRENT MONITOR:
0 to +10 V equivalent to 0 to rated current.
Accuracy: 1 kV to 6 kV: 1.5% of setting plus 0.5% of rated output.8 kV to 100 kV: 1% of setting plus 0.2% of rated output. Output impedance is 10K Ohm differentially coupled.